The Boston Diaries

The ongoing saga of Sean Conner, who doesn't live in Boston, nor does he even like Boston, but yet named his weblog/journal “The Boston Diaries.”

Go figure.

Sunday, October 11, 2026

The closet situation has been resolved

Longer than I care to admit it (like “months” longer) the clothing rod in the closet had partically collapsed. The weight of the clothes on the rod pull both brackets holding it down about 30°. The bracket is a thick piece of metal at right angles, with a cross piece of metal at a 45° angle, forming a triangle. At the end of the horizontal segment is a curved piece of metal to hold a rod. The support bracket used to be straight, but was bent nearly in right angles itself. And since the bracket was attached not only to the back wall, but a shelf sitting on it, the shelf itself had partially sagged. At the time, I removed some of the heavier items from the shelf, and most of the clothes. Things got a bit cluttered.

Then I finally got a round tuit and decided it was time to tackle the closet. It only took seven trips to various hardware stores to get it fixed properly.

Trip one—a hardware store around the corner from Chez Boca. They had two similar (but not identical) brackets in stock. I bought both, even though I wanted four in total to more evenly distribute the weight along the width of the closet (which spans the entire room). It turned out the brackets wouldn't have worked—the curved portion at the end of the bracket was right at the top edge.

Trip two—this time to Home Depot that's not around the corner from Chez Boca. There, they a better selection of brackets and more in stock. They had the exact brackets I needed, and some other ones that were made with thicker metal, with a triangular tube of metal as the cross piece, but the rod holder on the chonky bracket looked a bit too small. I bought one of each, plus some new screws, just in case. The chonky bracket looked like it would work—the rod holder just fit the rod.

That leads to trip three—get another chonky bracket, plus three of the other type for a total of four, just in case the chonky bracket didn't work out.

So I removed all the clothes and everything on the shelf above, leaving very little room in the room to work. Bunny has a whole bunch of tools; what we didn't have was a power tool for driving screws. Or rather, a power tool with a charged battery for driving screws. It was a painful, manual process of removing the screws still in place on the old brackets. Some one at some point had painted over the brackets and screws, and for one of the screws, I had to use some “percussive persuasion” to force the issue.

Then it was a painful, manual process of screwing in the new chonky brackets. I was able to reuse the existing screws, but I didn't bother screwing the horizontal portion to the shelf. The shelf itself was attached to a wooden beam along the back and side walls. I figured the shelf could just sit on the bracket such that if the brackets didn't work, they wouldn't pull the shelf down even more (and in writing circles, this is called “forshadowing”). I then rehung all the clothes and repopulated the shelf.

The next morning the clothing rod had completely collapsed. It had pulled the top screw from each bracket out of the wall. The brackets themselfs, the chonky ones, were fine—they weren't bent at all, they were just hanging from a single screw at the bottom. And it was here I was just about to give up. I even joked to Bunny that we should fly her brother out here to help. She agreed, and called her brother to make arrangements. But he refused to come out for 30 minutes of work, instead telling me what needs to be done.

“Get lag bolts,” he said. “They have hex heads, and Bunny should have a socket set. That will give you leverage to really screw them in.”

So trip four—back to Home Depot to get some lag bolts. And a replacement kit for the ends of the rods to attach to the side walls, as that was damaged by the second collapse.

Some pre-drilling (Bunny did have a chorded power drill, but it wasn't reversable so it couldn't be used to remove screws. It was also impossible to use it to drive the top screw into the bracket due to space issues), some elbow grease with the socket set, and we're back in business with the chonky brackets.

I added the clothes back to the rod and left it overnight. The rod was still up. I then replaced all the items back on the shelf, and it's still up in place.

Trip five—return the original two brackets I bought from the hardware store around the corner from Chez Boca.

Trip six—back to Home Depot to return the brackets I didn't use. I couldn't find the package of screws I originally purchased. I only found them later when I was cleaning the room after placing everything back in the closet.

So trip seven—back to Home Depot to return the package of screws I didn't use.

And finally we have our closet back.

Obligatory Picture

[Self-portrait with a Christmas Tree] Oh Chrismtas Tree!  My Christmas Tree!  Rise up and hear the bells!

Obligatory Contact Info

Obligatory Feeds

Obligatory Links

Obligatory Miscellaneous

Obligatory AI Disclaimer

No AI was used in the making of this site, unless otherwise noted.

You have my permission to link freely to any entry here. Go ahead, I won't bite. I promise.

The dates are the permanent links to that day's entries (or entry, if there is only one entry). The titles are the permanent links to that entry only. The format for the links are simple: Start with the base link for this site: https://boston.conman.org/, then add the date you are interested in, say 2000/08/01, so that would make the final URL:

https://boston.conman.org/2000/08/01

You can also specify the entire month by leaving off the day portion. You can even select an arbitrary portion of time.

You may also note subtle shading of the links and that's intentional: the “closer” the link is (relative to the page) the “brighter” it appears. It's an experiment in using color shading to denote the distance a link is from here. If you don't notice it, don't worry; it's not all that important.

It is assumed that every brand name, slogan, corporate name, symbol, design element, et cetera mentioned in these pages is a protected and/or trademarked entity, the sole property of its owner(s), and acknowledgement of this status is implied.

Copyright © 1999-2026 by Sean Conner. All Rights Reserved.